Havener Pistol-Grip Hydro Walk-Behind Mower 36, 48 & 5 Manual de usuario

Parts & Owner’s Manual36”, 48” & 52” Commercial Hydro-Drive MowersHavener Enterprises, Inc. • 368 S. Michigan Ave.Bradley, IL • 60915815.9

10Starting The Engine:DANGER: DO NOT OPERATE THE ENGINE IN A CONFINED SPACEWHERE DANGEROUS CARBON MONOXIDE FUMES CAN COLLECT.CARBON DIOXIDE IS ODORLES

11Turning The Mower To turn the mower in the direction you want to go, gently squeeze the side’s traction control lever (i.e. to go right,squeeze the

12Moving the Mower Without Turning on the Engine1. Push the parking lever to the “ON” position.2. Move the neutral lever to the position (figure 8)3.

13Changing The Height Of Cut:DANGER: BEFORE MAKING ANY ADJUSTMENTS AND/OR SERVICING YOUR MOWER, MAKE SURETHE MOWER IS ON LEVEL GROUND, BLADES DISENGA

14Figure 10Figure 11Figure 12Figure 13Adjusting the Deck: (refer to Figure 13)Changes to the cutting height can be achieved by repositioning the cutte

15GENERAL MAINTENANCEProper maintenance and adjustment of your hydro mower is necessary to keep the mower in good and safe condi-tion. The maintenance

16FuelDANGER: GASOLINE IS HIGHLY FLAMMABLE AND EXPLOSIVE. DO NOT ADD FUEL WHILE THE ENGINEIS RUNNING OR IS HOT. KEEP OPEN FLAMES, SPARKS, AND HEAT AW

17Lubrication PointsTo assure proper lubrication on moving parts, it is recommended that you lubricate the following componentswith a high-quality EP2

18SERVICE ADJUSTMENTSDANGER: BEFORE MAKING ANY ADJUSTMENTS AND/OR SERVICING YOUR MOWER, MAKE SURE THEMOWER IS ON LEVEL GROUND, BLADES DISENGAGED, KEY

19Figure 15Engine To Blade Belt Adjustment for 48” and 52” (Refer to Figure 15)1. Remove the deck cover and move the blade control lever on the contro

TABLE OF CONTENTSAbout This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20Figure 17Figure 18Safety System Adjustment (Refer to figure 18 & 19)DANGER: DO NOT BYPASS, MODIFY, ALTER, OR DISCONNECT THE SAFETYSYSTEM. MAKE

215. Turn adjustment nut”A” just until the wheel turns rearward. Make a note of the position of the adjustment nut. To adjust to neutral, split the di

22TROUBLE SHOOTINGProblem Possible Cause SolutionEngine Does Not Start Key in the OFF position Turn key to ONSpeed control lever not in the Move lever

23TROUBLE SHOOTINGProblem Possible Cause SolutionMower Does Not Move Transmission is in neutral Move transmission lever (page 9)When Traction Levers

24NOTES_______________________________________________________________________________________________________________________________________________

25NOTES_______________________________________________________________________________________________________________________________________________

136” Frame AssemblyItem No. Part Number Description Qty1 336-001 Hood 36" 12 100-009 Saucer Nut 43 300-001 Rear Deck Weldment 14 200-006 Nylon Nu

248” & 52” Frame AssemblyItem No. Part Number Description Qty1 100-009 Saucer Nut 32 348-001 Hood 48" 12 352-001 Hood 52" 13 300-001 Rea

336” Front Deck Assembly

436” Front Deck AssemblyItem Part No Description Qty Item Part No Description Qty1 300-002 Idler Pulley 2 29 200-024 Lock Washer 8 GB93-87 42 336-004

3NOTES________________________________________________________________________________________________________________________________________________

548” & 52” Front Deck Assembly

648” & 52” Front Deck AssemblyItem Part No Description Qty Item Part No Description Qty1 300-002 Idler Pulley 1 28 200-006 Nylon Nut M10 GB889-86

736”, 48” & 52” Brake & Wheel Assembly

836”, 48” & 52” Brake & Wheel AssemblyItem No. Part Number Description Qty1 200-004 Hexagon Bolt M12*25GB5783-86 12 200-071 Plain Washer 23 30

936”, 48” & 52” Transmission Drive Assembly

1036”, 48” and 52” Transmission Drive AssemblyItem No. Part Number Description Qty1 300-032 Pivot Hub 12 300-033 Bushing, Straight, Pivot 23 300-131

1136”, 48” & 52” Rear Deck Assembly

1236”, 48” & 52” Rear Deck AssemblyItem No. Part Number Description Qty1 N/A Engine Assembly 12 200-029 Nut Flange M8 GB187-86 23 300-059 Discharg

1336”, 48” & 52” Handle Control Assembly

1436”, 48” & 52” Handle Control AssemblyItem No. Part Number Description Qty1 100-084 OPC Lever RH 12 100-085 OPC Lever LH 13 100-083 Flange Bush

4About This ManualThis owner’s manual is considered a permanent part of the mower. It must be available to all ofthe operators and/or person(s) servic

1536”, 48” & 52” Front Caster AssemblyItem No. Part Number Description Qty1 100-127 Front Wheel Washer 42 200-056 Bearing 6003 2RS 43 100-093 Pi

1636”, 48” & 52” Fuel Tank AssemblyItem No. Part Number Description Qty1 100-102 Fuel Tank Cap 12 100-103 Fuel Tank Body 13 100-104 Fuel Tank Str

1736”, 48” & 52” Electrical ComponentsItem No. Part Number Description Qty1 300-082 Switch 42 200-062 Wire Tie 43&4 100-114 Key Switch &

PURCHASER INFORMATIONFirst Name: _________________________ Last Name: _________________________________Business Name: ________________________________

19NOTES_______________________________________________________________________________________________________________________________________________

20NOTES_______________________________________________________________________________________________________________________________________________

5Warranty StatementThis mower is warranted for one (1) year from the original date of purchase against defects inmaterial or workmanship, when operate

6SAFETY INFORMATIONRead This Manual Carefully And Thoroughly Before Operating The Mower!Training1. Carefully and thoroughly read the owner’s manual. A

7Operation of EquipmentDANGER: GASOLINE IS HIGHLY FLAMMABLE AND EXPLOSIVE. DO NOT ADD FUEL WHILE THEENGINE IS RUNNING OR IS HOT. KEEP OPEN FLAMES, SP

8SAFETY INFORMATION DECALSThe following labels are intended to alert you to potential hazards and to provide youwith important safety information. Sho

9OPERATING THE MOWERIt is recommended that before you operate the mower, you allow adequate time to fully understandthe controls and operation of the